PRESSURE TRANSMITTER

Pressure transmitters are essential instrumentation devices used in industrial process control to convert pressure values into electrical signals. They are commonly available in two types for pressure measurement: Gauge Pressure Transmitters and Absolute Pressure Transmitters.

Gauge Pressure Transmitters

Gauge pressure transmitters calculate the measured pressure relative to a reference pressure, which is typically atmospheric pressure (1 atm). Therefore, they measure pressure as either positive or negative relative to atmospheric pressure. In other words, the measured pressure is expressed as the difference from atmospheric pressure. Gauge pressure transmitters can also measure negative pressure values when the measured pressure is below atmospheric pressure. These transmitters are commonly used for pressure measurement of gases and liquids.

Absolute Pressure Transmitters

Absolute pressure transmitters measure the absolute pressure of the process medium. Absolute pressure is referenced to a perfect vacuum rather than atmospheric pressure. As a result, absolute pressure transmitters always display positive values regardless of atmospheric pressure. These transmitters are commonly used in vacuum applications, altitude measurements above sea level, and closed systems.

Both types of pressure transmitters are widely used in industrial process control, automation, power generation, chemical and petrochemical industries, aerospace, automotive, and many other sectors to provide reliable and accurate pressure measurement. The appropriate transmitter type is selected according to the characteristics of the process and application requirements.

The output signal is a load-independent 4–20 mA DC signal or a PROFIBUS PA or FOUNDATION™ Fieldbus signal that is linearly proportional to the input pressure. Communication is available via the HART protocol, PROFIBUS PA, or FOUNDATION™ Fieldbus interface. Basic transmitter configuration can be easily performed locally using three push buttons.

Benefits

High quality and long service life
High reliability even under extreme chemical and mechanical loads
Comprehensive diagnostic and simulation functions
Minimal conformity error
Low long-term drift
Wetted parts manufactured from high-quality materials (e.g., stainless steel, Hastelloy)
Measurement range from 0.008 bar to 400 bar (0.1 psi to 5802 psi)
High measurement accuracy
Parameter configuration via local control buttons and HART, PROFIBUS PA, and/or FOUNDATION™ Fieldbus

Applications

The pressure transmitter is available in both gauge pressure and absolute pressure versions. The output signal is always a load-independent 4–20 mA DC signal or a PROFIBUS PA or FOUNDATION™ Fieldbus signal that is linearly proportional to the input pressure. The pressure transmitter measures corrosive, non-corrosive, and hazardous gases, vapors, and liquids.

It can be used for the following measurement types:

Gauge Pressure
Absolute Pressure

With appropriate parameter configuration, it can also be used for the following additional measurement applications:

Level
Volume
Mass

The transmitter is available in an intrinsically safe Ex ia version for installation in hazardous areas (Zone 1). The devices are supplied with an EC Type Examination Certificate and comply with the relevant harmonized European ATEX standards.

Gauge Pressure

This version measures the gauge pressure of corrosive, non-corrosive, and hazardous gases, vapors, and liquids.

The minimum measurement range is 0.01 bar (0.15 psi), and the maximum measurement range is 400 bar (5802 psi).

Level Measurement

With appropriate parameter configuration, the gauge pressure version can also measure the level of corrosive, non-corrosive, and hazardous liquids.

For level measurement in an open vessel, a single transmitter is required. For level measurement in a closed vessel, two transmitters and a process control system are required.

Absolute Pressure

This version measures the absolute pressure of corrosive, non-corrosive, and hazardous gases, vapors, and liquids.

The minimum measurement range is 0.008 bara (0.12 psia), and the maximum measurement range is 30 bara (435 psia).

Technical Specifications

Gauge and Absolute Pressure Transmitters
Gauge Pressure Input
Measured Variable	Gauge Pressure
Measurement Range (continuously adjustable) or Nominal Measurement Range, Maximum Permissible Operating Pressure (in accordance with the Pressure Equipment Directive 2014/68/EU), and Maximum Permissible Test Pressure (in accordance with DIN 16086). (For oxygen measurement: maximum 100 bar / 10 MPa / 1450 psi at an ambient/process temperature of 60°C (140°F).)	HART	PROFIBUS PA/FOUNDATION Fieldbus
	Measurement Range	Nominal Measurement Range	Maximum Permissible Working Pressure (MAWP) (PS)	Maximum Permissible Test Pressure
	8,3 ... 250 mbar 0,83 ... 25 kPa 0,12 ... 3,6 psi	250 mbar 25 kPa 3,6 psi	4 bar400 kPa 58 psi	6 bar600 kPa 87 psi
	0,01 ... 1 bar 1 ... 100 kPa 0,15 ... 14,5 psi	1 bar100 kPa 14,5 psi	4 bar400 kPa 58 psi	6 bar600 kPa 87 psi
	0,04 ... 4 bar 4 ... 400 kPa 0,58 ... 58 psi	4 bar400 kPa 58 psi	7 bar/0,7 MPa 102 psi	10 bar1 MPa 145 psi
	0,16 ... 16 bar 16 ... 1600 kPa 2,3 ... 232 psi	16 bar 1600 kPa 232 psi	21 bar 2,1 MPa 305 psi	32 bar 3,2 MPa 464 psi
	0,63 ... 63 bar 63 ... 6300 kPa 9,1 ... 914 psi	63 bar6300 kPa 914 psi	67 bar / 6,7 MPa 972 psi	100 bar10 MPa 1450 psi
	1,6 ... 160 bar 0,16 ... 16 MPa 23 ... 2321 psi	160 bar16 MPa 2321 psi	167 bar / 16,7 MPa 2422 psi	250 bar 25 MPa 3626 psi
	4 ... 400 bar 0,4 ... 40 MPa 58 ... 5802 psi	400 bar40 MPa 5802 psi	400 bar40 MPa 5802 psi	600 bar60 MPa 8702 psi
Lower Measurement Limit For 250 mbar / 25 kPa / 3.6 psi measuring cells, the lower measurement limit is 750 mbar abs / 75 kPa abs / 10.8 psia. The measuring cell is vacuum-resistant down to 30 mbar abs / 3 kPa abs / 0.44 psia.
Silicone Oil-Filled Measuring Cell	30 mbar a/3 kPa a/0,44 psi a
Measuring Cell with Inert Fill Fluid	30 mbar a/3 kPa a/0,44 psi a
Upper Measurement Limit	100% of the maximum measuring range (for oxygen measurement: maximum 100 bar / 10 MPa / 1450 psi and an ambient temperature of 60°C (140°F)).
Absolute Pressure Input
Measured Variable	Absolute Pressure
Measurement Range (continuously adjustable) or Nominal Measurement Range, Maximum Permissible Operating Pressure (in accordance with the Pressure Equipment Directive 2014/68/EU), and Maximum Permissible Test Pressure (in accordance with DIN 16086).	HART	PROFIBUS PA/FOUNDATION Fieldbus
	Measurement Range	Nominal Measurement Range	Maximum Permissible Working Pressure (MAWP) (PS)	Maximum Permissible Test Pressure
	8,34 ... 250 mbar 0,83 ... 25 kPa 3,35 ... 100 inH 2 O a 0,13 ... 3,63 psi a	250 mbar 25 kPa a 100 inH 2 O a	1,5 bar - 150 kPa - 21,8 psi	6 bar 600 kPa 87 psi
	43,34 ... 1300 mbar -de 4,33 ... 130 kPa -de 17,42 ... 522,4 inH2O -de 0,63 ... 18,86 psia	1300 mbar - 130 kPa - 525 inH 2 O -	2,6 bar - 260 kPa - 37,7 psi	10 bar 1 MPa 145 psi
	0,17 ... 5 bar 17 ... 500 kPa 2,43 ... 72,5 psi	5000 mbar - 500 kPa - 72,5 psi	10 bar 1 MPa 145 psi	30 bar 3 MPa 435 psi
	1 ... 30 bar 0,1 ... 3 MPa 14,6 ... 435 psi	30 bar 3 MPa 435 psi	45 bar 4,5 MPa 653 psi	100 bar 10 MPa 1450 psi
Lower Measurement Limit
Silicone Oil-Filled Measuring Cell	0 mbar a/3 kPa a/0,44 psi a
Measuring Cell with Inert Fill Fluid
For Ambient Temperatures of -20°C < ϑ ≤ +60°C (-4°F < ϑ ≤ +140°F)	30 mbar a/0 kPa a/0 psi a
For Ambient Temperatures of 60°C < ϑ ≤ +100°C (Maximum 85°C for the 30 bar Measuring Cell) (140°F < ϑ ≤ +212°F (Maximum 185°F for the 435 psi Measuring Cell))	30 mbar a + 20 mbar a · (ϑ -60 °C)/°C 3 kPa a + 2 kPa a · (ϑ -60 °C)/°C 0,44 psi a + 0,29 psi a · (ϑ - 140 °F )/°F
Upper Measurement Limit	100% max. measuring range (for oxygen measurement: max. 100 bar / 10 MPa / 1450 psi and 60 °C (140 °F) ambient/process temperature)
Lower Range Value (LRV)	Between the measurement limits (continuously adjustable)
Gauge Pressure Input with Flush-Mounted Diaphragm
Measured Variable	Gauge pressure, flush-mounted
Measurement Range (continuously adjustable) or Nominal Measurement Range, Maximum Permissible Operating Pressure, and Maximum Permissible Test Pressure.	HART	PROFIBUS PA/FOUNDATION Fieldbus
	Measurement Range	Nominal Measurement Range	Maximum Permissible Working Pressure (MAWP) (PS)	Maximum Permissible Test Pressure
	0,01 ... 1 bar 1 ... 100 kPa 0,15 ... 14,5 psi	1 bar100 kPa 14,5 psi	4 bar400 kPa 58 psi	6 bar600 kPa 87 psi
	0,04 ... 4 bar 4 ... 400 kPa 0,58 ... 58 psi	4 bar400 kPa 58 psi	7 bar/0,7 MPa 102 psi	10 bar1 MPa 145 psi
	0,16 ... 16 bar 16 ... 1600 kPa 2,3 ... 232 psi	16 bar 1600 kPa 232 psi	21 bar 2,1 MPa 305 psi	32 bar 3,2 MPa 464 psi
	0,63 ... 63 bar 63 ... 6300 kPa 9,1 ... 914 psi	63 bar6300 kPa 914 psi	67 bar / 6,7 MPa 972 psi	100 bar10 MPa 1450 psi
Lower Measuring Range Limit	100 mbar bir (1,45 psi bir)
Silicone oil-filled measuring cell	100 mbar a/10 kPa a/1,45 psi a
Inert liquid-filled measuring cell	100 mbar a/10 kPa a/1,45 psi a
Neobee® oil-filled measuring cell	100 mbar a/10 kPa a/1,45 psi a
Upper Measuring Range Limit	%100 maks. ölçüm aralığı
Absolute Pressure Input with Flush-Mounted Diaphragm
Measured Variable	Flush-mounted absolute pressure
Measuring Range (Continuously Adjustable) or Nominal Measuring Range and Maximum Permissible Test Pressure	HART	PROFIBUS PA/FOUNDATION Fieldbus
	Measuring Range	Nominal Measuring Range	Maximum Allowable Working Pressure (MAWP / PS)	Maximum Permissible Test Pressure
	43 ... 1300 mbar 4,3 ... 130 kPa 17 ... 525 inH 2 O a	1300 mbar - 130 kPa - 525 inH 2 O -	2,6 bar - 260 kPa - 37,7 psi	10 bar 1 MPa 145 psi
	160 ... 5000 mbar 16 ... 500 kPa 2,32 ... 72,5 psi	5000 mbar - 500 kPa - 72,5 psi	10 bar 1 MPa 145 psi	30 bar 3 MPa 435 psi
	1 ... 30 bar 0,1 ... 3 MPa 14,5 ... 435 psi	30 bar 3 MPa 435 psi	45 bar 4,5 MPa 653 psi	100 bar 10 MPa 1450 psi
	Depending on the process connection, the measuring range may differ from these values.
Lower Measuring Range Limit	0 mbar a/0 kPa a/0 psi a
Upper Measuring Range Limit	100% of the maximum measuring range
Output	HART		PROFIBUS PA/FOUNDATION Fieldbus
Output Signal	4 ... 20 mA		Digital PROFIBUS PA signal
Physical Bus	-		IEC 61158‑2
Reverse Polarity Protection	Protected against short circuits and reverse polarity. Each connection is protected against the maximum supply voltage.		Protected against short circuits and reverse polarity. Each connection is protected against the maximum supply voltage.
Electrical Damping (0.1 s Increments)	Adjustable from 2 s (0...100 s)		Adjustable to 2 s (0...100 s)
Measurement Accuracy for Gauge Pressure	According to IEC 62828-1
Reference Conditions	Ascending characteristic curve Lower range value: 0 bar Stainless steel sealing diaphragm Silicone oil-filled measuring cell Ambient temperature: 25°C (77°F)
Turndown Ratio (Span, Turn-down)	r = Maximum measuring range / Set measuring range or nominal measuring range
Limit Setting Deviation Including Hysteresis and Repeatability
Linear Characteristic Curve
250mbar/25kPa/3,6psi	r ≤ 1,25: ≤ %0,075 1,25 < r ≤ 30: ≤ (0,008 · r +0,065)%
1 bar/100 kPa/14,5 psi 4 bar/400 kPa/58 psi 16 bar/1,6 MPa/232 psi 63 bar/6,3 MPa/914 psi 160 bar/16 MPa/2321 psi	r ≤ 5: ≤ %0,075 5 < r ≤ 100: ≤ (0,005 · r +0,05)%
400 bar/40 MPa/5802 psi	r ≤ 3: ≤ %0,075 3 < r ≤ 10: ≤ (0,0029 · r +0,071)% 10 < r ≤ 100: ≤ (0,005 · r +0,05)%
Effect of Ambient Temperature (per 28°C (50°F))
250mbar/25kPa/3,6psi	≤ (0,16 · r +0,1)%
1 bar/100 kPa/14,5 psi 4 bar/400 kPa/58 psi 16 bar/1,6 MPa/232 psi 63 bar/6,3 MPa/914 psi 160 bar/16 MPa/2321 psi 400 bar/40 MPa/5802 psi	≤ (0,07 · r +0,08)%
Long-Term Stability (Temperature Change ±30°C (±54°F))
250mbar/25kPa/3,6psi	≤ (0,16 · r) yıllık %
1 bar/100 kPa/14,5 psi 4 bar/400 kPa/58 psi	5 yılda ≤ (0,25 · r)%
16 bar/1,6 MPa/232 psi 63 bar/6,3 MPa/914 psi 160 bar/16 MPa/2321 psi 400 bar/40 MPa/5802 psi	5 yılda ≤ (0,125 · r)%
Effect of Mounting Position	≤ 0.05 mbar / 0.005 kPa / 0.000725 psi per 10° of inclination (zero offset can be compensated by position error correction).
Effect of Auxiliary Power (per voltage change)	≤ 0.005% per 1 V
Measured Value Resolution for PROFIBUS PA and FOUNDATION Fieldbus	3 × 10⁻⁵ of the nominal measuring range
Measurement Accuracy for Absolute Pressure	According to IEC 62828-1
Reference Conditions (All error specifications always refer to the calibrated measuring range.)	Ascending characteristic curve Lower range value: 0 bar Stainless steel sealing diaphragm Silicone oil fill Ambient temperature: 25°C (77°F)
Turndown Ratio (Span, Turn-down) r	r = Maximum measuring range / Calibrated measuring range or nominal measuring range
Limit Setting Deviation Including Hysteresis and Repeatability
Linear Characteristic Curve
r ≤ 10	≤ 0.1%
10 < r ≤ 30	≤ 0.2%
Effect of Ambient Temperature (per 28°C (50°F))
250 mbar a/25 kPa a/3,6 psi a	≤ (0,15 · r +0,1)%
1300 mbar a/130 kPa a/18,8 psi a 5 bar a/500 kPa a/72,5 psi a 30 bar a/3000 kPa a/435 psi a	≤ (0,08 · r +0,16)%
Long-Term Stability (Temperature Change ±30°C (±54°F))	5 year ≤ (0,25 · r)%
Effect of Mounting Position (Pressure per Change in Inclination Angle)	≤ 0.05 mbar/0.005 kPa/0.000725 psi per 10° slope (zero-point correction is possible with position error compensation)
Effect of Auxiliary Power (per Voltage Change)	≤ 0.005% per 1 V
Measured Value Resolution for PROFIBUS PA and FOUNDATION Fieldbus	3 × 10⁻⁵ of the nominal measuring range
Measurement Accuracy for Gauge and Absolute Pressure with Flush-Mounted Diaphragm	According to IEC 62828-1
Reference Conditions (All error specifications always refer to the calibrated measuring range.)	Ascending characteristic curve Lower range value: 0 bar Stainless steel sealing diaphragm Silicone oil fill Ambient temperature: 25°C (77°F)
Turndown Ratio r (Span, Turn-down)	r = Maximum measuring range / Calibrated measuring range or nominal measuring range
Limit Setting Deviation Including Hysteresis and Repeatability
Linear Characteristic Curve	Flush-Mounted Gauge Pressure		Flush-Mounted Absolute Pressure
r ≤ 5	≤ 0.075%		-
5 < r ≤ 100	≤ (0,005 · r +0,05)%		-
r ≤ 10	-		≤ 0.2%
10 < r ≤ 30	-		≤ 0.4%
Effect of Ambient Temperature (per 28°C (50°F))	≤ (0,08 · r +0,16)%		≤ (0,16 · r +0,24)%
Temperature Difference Between Process Temperature and Ambient Temperature
Effect of Ambient Temperature (Pressure per Unit Temperature Change)	3 mbar / 0.3 kPa / 0.04 psi per 10 K
Long-Term Stability (Temperature Change ±30°C (±54°F))	≤ (0.25 × r)% over 5 years
Effect of Mounting Position (Pressure per Change in Inclination Angle)	≤ 0.4 mbar / 0.04 kPa / 0.006 psi per 10° of inclination (zero offset can be corrected by position error compensation)
Effect of Auxiliary Power (per Voltage Change)	≤ 0.005% per 1 V
Measured Value Resolution for PROFIBUS PA and FOUNDATION Fieldbus	3 × 10⁻⁵ of the nominal measuring range

Operating Conditions
Installation Conditions
Ambient Temperature	Observe the temperature class requirements in hazardous areas.
Silicone oil-filled measuring cell	-40 ... +85 °C (-40 ... +185 °F)
			Neobee® Oil-Filled Measuring Cell (FDA-Compliant, Flush-Mounted Diaphragm)	-10 ... +85 °C (14 ... 185 °F)
Inert Liquid-Filled Measuring Cell	-40 ... +85 °C (-40 ... +185 °F)
			Readable Display	-30 ... +85 °C (-22 ... +185 °F)
Storage Temperature	-50 ... +85 °C (-58 ... +185 °F)

	For Neobee® oil: -20...+85°C (-4...+185°F)

	For high-temperature oil: -10...+85°C (14...+185°F)

Climatic Class
			Condensation	Relative humidity: 0...100%

Condensation permitted; suitable for use in tropical climates.

Degree of Protection
According to IEC 60529	IP65, IP68
			According to NEMA 250	Type 4X enclosure, suitable for washdown applications, resistant to alkaline cleaning agents, and steam-cleanable up to 150°C (302°F).
Electromagnetic Compatibility (EMC)
Emitted Interference and Immunity	According to IEC 61326 and NAMUR NE 21
			Process Conditions
Process Temperature	For flush-mounted process connections, the maximum process temperature shall comply with the applicable connection standards (e.g., DIN 32676, DIN 11851, etc.).
Silicone Oil-Filled Measuring Cell	-40 ... +100 °C (-40 ... +212 °F)
			Silicone oil-filled measuring cell (flush-mounted diaphragm)	-40 ... +150 °C (-40 ... +302 °F)
Neobee oil-filled measuring cell (FDA-compliant, flush-mounted diaphragm)	-10 ... +150 °C (14 ... 302 °F)
			Silicone oil-filled measuring cell with temperature isolator (only for the flush-mounted diaphragm gauge pressure version)	-40 ... +200 °C (-40 ... +392 °F)
Neobee oil-filled measuring cell with temperature isolator (only for the flush-mounted diaphragm gauge pressure version)	-10 ... +200 °C (14 ... 392 °F)
			Measuring cell with inert fluid	-20 ... +100 °C (-4 ... +212 °F)
Mechanical design (standard version)
Weight (without options)	Approx. 800 g (1.8 lb)
Housing material	Stainless steel, mat. No. 1.4301/304
Materials of wetted parts
Connection stem	Stainless steel, mat. No. 1.4404/316L or Hastelloy C276, mat. No. 2.4819
			Oval flange	Stainless steel, mat. No. 1.4404/316L
Seal diaphragm	Stainless steel, mat. No. 1.4404/316L or Hastelloy C276, mat. No. 2.4819
			Measuring cell fill	Silicone oil

Inert fill fluid

Process connection	G½B according to EN 837-1

	Female thread ½-14 NPT

	Mounting threaded oval flange PN 160 (MAWP 2320 psi):



	7/16-20 UNF according to IEC 61518 / EN 61518

	M10 according to DIN 19213

Mechanical design
(flush-mounted diaphragm version)
Weight (without options)	Approx. 1 ... 13 kg (2.2 ... 29 lb)
Housing material	Stainless steel, mat. No. 1.4301/304
Materials of wetted parts
Process connection	Stainless steel, mat. No. 1.4404/316L
			Seal diaphragm	Stainless steel, mat. No. 1.4404/316L
Measuring cell fill	Silicone oil

	Inert fill fluid

	Food-grade oil (Neobee oil)

Process connection	EN and ASME compliant flanges

	F&B and pharmaceutical flanges

Surface finish of wetted parts	Ra values ≤ 0.8 µm (32 µin) / welds Ra ≤ 1.6 µm (64 µin)

	(3-A process connections; Ra values ≤ 0.8 µm (32 µin) / welds Ra ≤ 0.8 µm (32 µin)
Auxiliary power UH	HART	PROFIBUS PA/FOUNDATION Fieldbus
Terminal voltage at the transmitter	10,5 ... 42 V DC	-

	10.5 ... 30 V DC for intrinsically safe operation
Auxiliary power	-	Bus-powered
Separate supply voltage	-	Not required
Bus voltage
Ex olmadan	-	9 ... 32V
			With intrinsically safe operation	-	9 ... 24V
Instantaneous current consumption
Max. basic current	-	12,5 mA
			Start-up current ≤ basic current	-	Evet
Max. fault current in case of a fault	-	15,5 mA
			Fault Disconnection Electronics (FDE) available	-	Evet
Sertifikalar ve onaylar	HART	PROFIBUS PA/FOUNDATION Fieldbus
Classification according to the Pressure Equipment Directive (PED 2014/68/EU)	1. akışkan grubu gazları ve 1. akışkan grubu sıvıları için; Madde 4, Paragraf 3 gerekliliklerine uygundur (sağlam mühendislik uygulaması)
Water, wastewater	Available soon
Explosion protection
Intrinsic safety "i"	PTB 05 ATEX 2048
Marking	II1/2 G Exia llC/llB T4/T5/T6 Ga/Gb
			Permissible ambient temperature
Temperature class T4	-40 ... +85 °C (-40 ... +185 °F)
			Temperature class T5	-40 ... +70 °C (-40 ... +158 °F)
Temperature class T6	-40 ... +60 °C (-40 ... +140 °F)
			Connection	To certified intrinsically safe circuits with peak values:	To certified intrinsically safe circuits with peak values:

U ben = 30 V, ben = 100 mA, P ben = 750 mW, R ben = 300 Ω	FISCO power supply:

	U ben = 17,5 V, ben = 380 mA, P ben = 5,32 W

	Linear barrier:

	U ben = 24 V, ben = 250 mA, P ben = 1,2 W
Etkili dahili kapasitans	Ci = 6 nF	Ci = 1.1 nF
			Effective internal inductance	L ben = 0.4 mH	Li = 7 uH
Explosion protection according to FM for USA and Canada (cFM US)
Identification (DIP) or (IS); (NI)	Certificate of Compliance 3025099

	CL I, DIV 1, GP ABCD T4 ... T6; CL II, DIV 1, GP EFG; CLIII; CL I, ZN 0/1 AEx ia IIC T4 ... T6

	CL I, DIV 2, GP ABCD T4 ... T6; CL II, DIV 2, GP FG; KL III
Identification (DIP) or (IS)	Certificate of Compliance 3025099C

	CL I, DIV 1, GP ABCD T4 ... T6; CL II, DIV 1, GP EFG; CLIII; Ex ia IIC 4 ... T6

	CL I, DIV 2, GP ABCD T4 ... T6; CL II, DIV 2, GP FG; KL III
Dust explosion protection for Zone 20/21/22	PTB 05 ATEX 2048
Marking	II 1 D Ex ia lllC T120 °C Da

	II 1/2 D Ex ia lllC T120 °C Da/Db

	II 2 D Ex ib lllC T120 °C Db
Permissible ambient temperature
			Temperature class T4	-40 ... +85 °C (-40 ... +185 °F) (mineral cam pencere için -20 ... +85 °C (-4 ... +185 °F))
Temperature class T5	-40 ... +70 °C (-40 ... +158 °F) (mineral cam pencere için -20 ... +70 °C (-4 ... +158 °F))
			Temperature class T6	-40 ... +60 °C (-40 ... +140 °F) (mineral cam pencere için -20 ... +60 °C (-4 ... +140 °F))
Connection	To certified intrinsically safe circuits with peak values:	To certified intrinsically safe circuits with peak values:

	Ui = 30V, Ii = 100mA , Pi = 750mW	U ben = 24 V, Ii = 380 mA, P ben = 5,32 W
Etkili dahili kapasitans	Ci = 6 nF	Ci = 5 nF
			Effective internal inductance	Li = 0,4 uH	Li = 10 uH
Protection type Ex nA/nL/ic (Zone 2)	PTB 05 ATEX 2048
Marking	II 2/3 G Ex ic llC/llB T4/T5/T6 Gb/Gc

	II 2/3 G Ex nA llC T4/T5/T6 Gb/Gc
Permissible ambient temperature
			Temperature class T4	-40 ... +85 °C (-40 ... +185 °F) (yalnızca mineral cam pencere için -20 ... +85 °C (-4 ... +185 °F))
Temperature class T5	-40 ... +70 °C (-40 ... +158 °F) (yalnızca mineral cam pencere için -20 ... +70 °C (-4 ... +158 °F))
			Temperature class T6	-40 ... +60 °C (-40 ... +140 °F) (yalnızca mineral cam pencere için -20 ... +60 °C (-4 ... +140 °F))
Ex nA/nL bağlantısı	To certified intrinsically safe circuits with peak values:	To certified intrinsically safe circuits with peak values:

	Um = 45V	Um = 32V
Old link	To certified intrinsically safe circuits with peak values:	To certified intrinsically safe circuits with peak values:

	U ben = 45 V	U ben = 32 V
Effective internal capacitance	Ci = 6 nF	Ci = 5 nF

Communication

Communication
HART
HART	230 ... 1100 Ω
Protocol	HART version
PC software	SIMATIC PDM
PROFIBUS PA
Simultaneous communication with Master Class 2 (max.)	4
Address configurable	Via configuration tool or local operation (default setting: Address 126)
Cyclic data usage
• Output bytes	5 (one measured value) or 10 (two measured values)
• Input bytes	0, 1 or 2 (totalizer mode for batching and reset function)
Internal data processing
Device profile	PROFIBUS PA Profile for Process Control Devices Version 3.0, Class B
Function blocks	2
• Analog input
User-specific process variable adaptation	Yes, linear increasing or decreasing characteristic curve
Adjustable electrical damping	0 ... 100 s
Simulation function	Output/Input
Failure mode	Parameterizable (last good value, substitute value, faulty value)
Limit monitoring	Yes, one upper and one lower warning limit and one alarm limit
Totalizer	Resettable, presettable, selectable counting direction, simulation function for totalizer output
Failure mode	Parameterizable (totalizing with last good value, continuous totalizing, totalizing with faulty value)
Limit monitoring	One upper and one lower warning limit and one alarm limit
Physical block	1
Transducer blocks	2
• Pressure transducer block
Two-pressure calibration	Yes
Sensor limit monitoring	Yes
Characteristic curve specification	Max. 30 nodes
Simulation function for measured pressure value and sensor temperature	Via fixed value or parameterizable ramp function
FOUNDATION Fieldbus
Function blocks	3 Analog Input function blocks, 1 PID function block
• Analog input
User-specific process variable adaptation	Yes, linear increasing or decreasing characteristic curve
Adjustable electrical damping	0 ... 100 s
Simulation function	Output/Input (can be locked by a bridge inside the device)
Failure mode	Parameterizable (last good value, substitute value, faulty value)
Limit monitoring	Yes, one upper and one lower warning limit and one alarm limit
Square-root characteristic curve for flow measurement	Yes
PID	Standard FOUNDATION Fieldbus function block
Physical block	1 Resource Block
Transducer blocks	1 Pressure Transducer Block, 1 LCD Transducer Block
• Pressure transducer block
Two-pressure calibration	Yes
Sensor limit monitoring	Yes
Simulation function: measured pressure value, sensor temperature and electronics temperature	Via fixed value or parameterizable ramp function